fpga系列 HDL：ModelSim显示模拟波形+十进制格式数值(临时方法和设置持久化的默认值)

模拟波形

• FPGA中使用数字滤波器时，可通过观察模拟波形更好地查看滤波效果。可以通过ModelSim中的波形格式设置来实现更直观的波形显示。
• 右键波形->Format-> Analog
  
• 效果
  

数值格式显示

• 不同的数值格式显示：右键波形->Radix-> Decimal
  
• 效果
  

临时设置格式

• 这个格式可在当前项目的中所有仿真中保持(不关闭窗口的每次重新仿真)，不用向上面一样没测设置https://ww1.microchip.com/downloads/aemDocuments/documents/FPGA/swdocs/modelsim/modelsim_user_2024_2.pdf
  

设置默认值

• 编辑modelsim.ini的DefaultRadix
  

示例代码

verilog

/*
- 输出 是否找到同步头- 找正峰- 尝试找到超过正阈值的点作为潜在的正峰。- 对每个可能的正峰，进一步检查它是否是局部最大值（通过比较接下来的12个样本），并记录峰值的位置。- 验证正峰后的负峰 :- 一旦找到一个正峰，检查其后大约18或24个样本处是否存在低于负阈值的负峰。- 如果找到了符合条件的负峰，则认为找到了一个同步信号的开始，
*/  module MySyncDetect (input wire reset,input wire CLK_for_FIFO,            // 同步FIFO控制信号input wire [15:0] DATA_FIR_from_DFIFO, // 来自FIFO的数据流input wire full_from_DFIFO,         // FIFO满标志input wire [11:0] usedw_from_DFIFO, // FIFO已用深度output reg sync_detected,           // 是否找到同步头output reg[2:0] state               // 状态机状态
);parameter SYNCLEN = 64;               // 同步长度参数，可以根据实际情况调整
parameter POS_THRESHOLD = 100;        // 正阈值
parameter NEG_THRESHOLD = -100;       // 负阈值
localparam DEPTH = 32;                // 数据缓冲区深度
localparam FIND_RANGE = 20;           // 数据缓冲区深度// 状态机定义
localparam IDLE = 3'b000;
localparam FIND_PEAK = 3'b001;
localparam CHECK_NEGATIVE_PEAK = 3'b010;
localparam SYNC_FOUND = 3'b011;
// reg [2:0] state;
reg [2:0] next_state;reg [15:0] data_buffer[0:DEPTH-1];    // 数据缓冲区
reg [4:0] buffer_index;               // 缓冲区索引
reg [4:0] peak_index;                 // 峰值索引
reg bPeak;                            // 是否找到峰值
reg bFirstTag;                        // 第一个标签标记integer i=0;
integer j;
integer k;// 初始化状态always @(posedge reset) beginif (reset) beginstate = IDLE;next_state = IDLE;buffer_index = 5'b0;end
end// 控制信号
wire valid_data = (usedw_from_DFIFO > 0);// && !full_from_DFIFO;
wire [15:0] current_data = DATA_FIR_from_DFIFO;// 时钟边沿触发过程
always @(posedge CLK_for_FIFO) beginif (valid_data) begin// 更新数据缓冲区data_buffer[buffer_index] <= current_data;buffer_index <= (buffer_index == DEPTH-1) ? 0 : buffer_index + 1;end// 状态机转换state <= next_state;
end// 下一状态逻辑
always @(posedge CLK_for_FIFO) begin// next_state = state;case (state)IDLE: beginif (valid_data)next_state = FIND_PEAK;endFIND_PEAK: begin// 查找正峰if(buffer_index>= 12)begini = buffer_index-12;end else begin i = buffer_index + DEPTH - 12;endif (data_buffer[i] > POS_THRESHOLD) begin// 确认是否为局部最大值bPeak = 1;for (j = 1; j < 12; j = j + 1) beginif (data_buffer[(i+j) % DEPTH] > data_buffer[i]) beginbPeak = 0;endend// 是局部最大值if (bPeak) beginpeak_index = i;next_state = CHECK_NEGATIVE_PEAK;endendendCHECK_NEGATIVE_PEAK: begin// 验证正峰后的负峰for (k = 18; k <= 24; k = k + 1) beginif (data_buffer[(peak_index+k) % DEPTH] < NEG_THRESHOLD) begin// 找到符合条件的负峰next_state = SYNC_FOUND;endendendSYNC_FOUND: begin// 已经找到同步头next_state = IDLE;endendcase
end// 输出逻辑
always @(posedge CLK_for_FIFO) beginsync_detected <= 0;case (state)SYNC_FOUND: beginsync_detected <= 1;enddefault: beginsync_detected <= 0;endendcase
endendmodule

tb

// Testbench for SyncDetect`timescale 1ns/1psmodule MySyncDetect_tb;// Inputsreg CLK_for_FIFO;reg [15:0] DATA_from_DFIFO;reg full_from_DFIFO;reg [11:0] usedw_from_DFIFO;integer i;// Outputwire sync_detected;wire[2:0] state;// Instantiate the Unit Under Test (UUT)M2SyncDetect uut (.CLK_for_FIFO(CLK_for_FIFO),.DATA_FIR_from_DFIFO(DATA_from_DFIFO),.full_from_DFIFO(full_from_DFIFO),.usedw_from_DFIFO(usedw_from_DFIFO),.sync_detected(sync_detected),.state(state));// Clock generationinitial beginCLK_for_FIFO = 0;forever #5 CLK_for_FIFO = ~CLK_for_FIFO; // 10 ns clock periodend// Stimulusinitial begin// Initialize inputsDATA_from_DFIFO = -16'd23000;full_from_DFIFO = 0;usedw_from_DFIFO = 12'd0;// Apply test cases#100;DATA_from_DFIFO = -16'd23000; // Example datausedw_from_DFIFO = 12'd1;#20;DATA_from_DFIFO = -16'd1; // Example datausedw_from_DFIFO = 12'd2;#30;DATA_from_DFIFO = 16'h1234; // Example datausedw_from_DFIFO = 12'd3;#50;DATA_from_DFIFO = 16'hDEAD; // Example datausedw_from_DFIFO = 12'd4;// Apply test cases#10;for (i = 0; i < 5; i = i + 1) beginDATA_from_DFIFO = -16'd23000 + i; // Example data with variationfull_from_DFIFO = (i % 2 == 0) ? 1 : 0;usedw_from_DFIFO = 12'd100 + i * 10;#20;endfor (i = 0; i < 20; i = i + 1) beginDATA_from_DFIFO = -16'd23000 + i*10; // Example data with variation#20;end#50;$stop; // End simulation// Apply test cases#100;DATA_from_DFIFO = -16'd23000; // Example datausedw_from_DFIFO = 12'd1;#20;DATA_from_DFIFO = -16'd1; // Example datausedw_from_DFIFO = 12'd2;#30;DATA_from_DFIFO = 16'h1234; // Example datausedw_from_DFIFO = 12'd3;#50;DATA_from_DFIFO = 16'hDEAD; // Example datausedw_from_DFIFO = 12'd4;// Apply test cases#10;for (i = 0; i < 5; i = i + 1) beginDATA_from_DFIFO = -16'd23000 + i; // Example data with variationfull_from_DFIFO = (i % 2 == 0) ? 1 : 0;usedw_from_DFIFO = 12'd100 + i * 10;#20;endfor (i = 0; i < 20; i = i + 1) beginDATA_from_DFIFO = -16'd23000 + i*10; // Example data with variation#20;endendendmodule