华为配置WLAN跨VLAN的三层漫游示例

业务需求

企业用户通过WLAN接入网络，以满足移动办公的基本需求。在覆盖区域内移动发生跨VLAN漫游时，不影响用户的业务使用。

组网需求

• AC组网方式：旁挂三层组网。
• DHCP部署方式：
  • AC作为DHCP服务器为AP分配IP地址。
  • 汇聚交换机SwitchB作为DHCP服务器为STA分配IP地址。
• 业务数据转发方式：直接转发。

数据规划

配置思路

1. 配置AP、AC和周边网络设备之间实现网络互通。
2. 配置AP上线。
   1. 创建AP组，用于将需要进行相同配置的AP都加入到AP组，实现统一配置。
   2. 配置AC的系统参数，包括国家码、AC与AP之间通信的源接口。
   3. 配置AP上线的认证方式并离线导入AP，实现AP正常上线。
3. 配置WLAN业务参数，实现STA访问WLAN网络功能。

当用户新开局时，对于AP的射频信道的设置，用户可根据网络规划手动指定，也可使用射频调优功能自动选择最佳信道。本例中采用射频调优功能自动选择最佳信道。

配置注意事项

操作步骤

1. 配置周边设备

   # 配置接入交换机SwitchA的GE0/0/1接口加入VLAN10和VLAN101、GE0/0/2接口加入VLAN10、VLAN101和VLAN102、GE0/0/3接口加入VLAN10和VLAN102，GE0/0/1和GE0/0/3接口的缺省VLAN为VLAN10。
   <HUAWEI> system-view
   [HUAWEI] sysname SwitchA
   [SwitchA] vlan batch 10 101 102
   [SwitchA] interface gigabitethernet 0/0/1
   [SwitchA-GigabitEthernet0/0/1] port link-type trunk
   [SwitchA-GigabitEthernet0/0/1] port trunk pvid vlan 10
   [SwitchA-GigabitEthernet0/0/1] port trunk allow-pass vlan 10 101
   [SwitchA-GigabitEthernet0/0/1] port-isolate enable
   [SwitchA-GigabitEthernet0/0/1] quit
   [SwitchA] interface gigabitethernet 0/0/2
   [SwitchA-GigabitEthernet0/0/2] port link-type trunk
   [SwitchA-GigabitEthernet0/0/2] port trunk allow-pass vlan 10 101 102
   [SwitchA-GigabitEthernet0/0/2] quit
   [SwitchA] interface gigabitethernet 0/0/3
   [SwitchA-GigabitEthernet0/0/3] port link-type trunk
   [SwitchA-GigabitEthernet0/0/3] port trunk pvid vlan 10
   [SwitchA-GigabitEthernet0/0/3] port trunk allow-pass vlan 10 102
   [SwitchA-GigabitEthernet0/0/3] port-isolate enable
   [SwitchA-GigabitEthernet0/0/3] quit
   # 配置汇聚交换机SwitchB的接口GE0/0/1加入VLAN10、VLAN101和VLAN102，接口GE0/0/2加入VLAN100，接口GE0/0/3加入VLAN101和VLAN102，并创建接口VLANIF100，地址为10.23.100.2/24。
   <HUAWEI> system-view
   [HUAWEI] sysname SwitchB
   [SwitchB] vlan batch 10 100 101 102
   [SwitchB] interface gigabitethernet 0/0/1
   [SwitchB-GigabitEthernet0/0/1] port link-type trunk
   [SwitchB-GigabitEthernet0/0/1] port trunk allow-pass vlan 10 101 102
   [SwitchB-GigabitEthernet0/0/1] quit
   [SwitchB] interface gigabitethernet 0/0/2
   [SwitchB-GigabitEthernet0/0/2] port link-type trunk
   [SwitchB-GigabitEthernet0/0/2] port trunk allow-pass vlan 100
   [SwitchB-GigabitEthernet0/0/2] quit
   [SwitchB] interface gigabitethernet 0/0/3
   [SwitchB-GigabitEthernet0/0/3] port link-type trunk
   [SwitchB-GigabitEthernet0/0/3] port trunk allow-pass vlan 101 102
   [SwitchB-GigabitEthernet0/0/3] quit
   [SwitchB] interface vlanif 100
   [SwitchB-Vlanif100] ip address 10.23.100.2 24
   [SwitchB-Vlanif100] quit
   # 配置Router的接口GE1/0/0加入VLAN101和VLAN102，创建接口VLANIF101并配置IP地址为10.23.101.2/24，创建接口VLANIF102并配置IP地址为10.23.102.2/24。
   <Huawei> system-view
   [Huawei] sysname Router
   [Router] vlan batch 101 102
   [Router] interface gigabitethernet 1/0/0
   [Router-GigabitEthernet1/0/0] port link-type trunk
   [Router-GigabitEthernet1/0/0] port trunk allow-pass vlan 101 102
   [Router-GigabitEthernet1/0/0] quit
   [Router] interface vlanif 101
   [Router-Vlanif101] ip address 10.23.101.2 24
   [Router-Vlanif101] quit
   [Router] interface vlanif 102
   [Router-Vlanif102] ip address 10.23.102.2 24
   [Router-Vlanif102] quit

2. 配置AC与其它网络设备互通

   # 配置AC的接口GE0/0/1加入VLAN100，并创建接口VLANIF100。
   <HUAWEI> system-view
   [HUAWEI] sysname AC
   [AC] vlan 100
   [AC-vlan100] quit
   [AC] interface vlanif 100
   [AC-Vlanif100] ip address 10.23.100.1 24
   [AC-Vlanif100] quit
   [AC] interface gigabitethernet 0/0/1
   [AC-GigabitEthernet0/0/1] port link-type trunk
   [AC-GigabitEthernet0/0/1] port trunk allow-pass vlan 100
   [AC-GigabitEthernet0/0/1] quit
   # 配置AC到AP的路由，下一跳为SwitchB的VLANIF100。
   [AC] ip route-static 10.23.10.0 24 10.23.100.2

3. 配置DHCP服务为AP和STA分配IP地址

   # 在SwitchB上配置DHCP中继，代理AC分配IP地址。
   [SwitchB] dhcp enable
   [SwitchB] interface vlanif 10
   [SwitchB-Vlanif10] ip address 10.23.10.1 24
   [SwitchB-Vlanif10] dhcp select relay
   [SwitchB-Vlanif10] dhcp relay server-ip 10.23.100.1
   [SwitchB-Vlanif10] quit
   # 在SwitchB上创建VLANIF101和VLANIF102接口为STA提供地址，并指定默认网关。​​​​​​​DNS服务器地址请根据实际需要配置。常用配置方法如下：
   接口地址池场景，需要在VLANIF接口视图下执行命令dhcp server dns-list ip-address &<1-8>。
   全局地址池场景，需要在IP地址池视图下执行命令dns-list ip-address &<1-8>。
   [SwitchB] interface vlanif 101
   [SwitchB-Vlanif101] ip address 10.23.101.1 24
   [SwitchB-Vlanif101] dhcp select interface
   [SwitchB-Vlanif101] dhcp server gateway-list 10.23.101.2
   [SwitchB-Vlanif101] quit
   [SwitchB] interface vlanif 102
   [SwitchB-Vlanif102] ip address 10.23.102.1 24
   [SwitchB-Vlanif102] dhcp select interface
   [SwitchB-Vlanif102] dhcp server gateway-list 10.23.102.2
   [SwitchB-Vlanif102] quit
   # 在AC上创建全局地址池为AP提供地址。
   [AC] dhcp enable
   [AC] ip pool huawei
   [AC-ip-pool-huawei] network 10.23.10.0 mask 24
   [AC-ip-pool-huawei] gateway-list 10.23.10.1
   [AC-ip-pool-huawei] option 43 sub-option 3 ascii 10.23.100.1
   [AC-ip-pool-huawei] quit
   [AC] interface vlanif 100
   [AC-Vlanif100] dhcp select global
   [AC-Vlanif100] quit

4. 配置AP上线

   # 创建AP组，用于将相同配置的AP都加入同一AP组中。
   [AC] wlan
   [AC-wlan-view] ap-group name ap-group1
   [AC-wlan-ap-group-ap-group1] quit
   [AC-wlan-view] ap-group name ap-group2
   [AC-wlan-ap-group-ap-group2] quit
   # 创建域管理模板，在域管理模板下配置AC的国家码并在AP组下引用域管理模板。
   [AC-wlan-view] regulatory-domain-profile name default
   [AC-wlan-regulate-domain-default] country-code cn
   [AC-wlan-regulate-domain-default] quit
   [AC-wlan-view] ap-group name ap-group1
   [AC-wlan-ap-group-ap-group1] regulatory-domain-profile default
   Warning: Modifying the country code will clear channel, power and antenna gain configurations of the radio and reset the AP. Continue?[Y/N]:y  
   [AC-wlan-ap-group-ap-group1] quit
   [AC-wlan-view] ap-group name ap-group2
   [AC-wlan-ap-group-ap-group2] regulatory-domain-profile default
   Warning: Modifying the country code will clear channel, power and antenna gain configurations of the radio and reset the AP. Continue?[Y/N]:y  
   [AC-wlan-ap-group-ap-group2] quit
   [AC-wlan-view] quit
   # 配置AC的源接口。
   V200R021C00版本开始，配置CAPWAP源接口或源地址时，会检查和安全相关的配置是否已存在，包括DTLS加密的PSK、AC间DTLS加密的PSK、登录AP的用户名和密码、全局离线管理VAP的登录密码，均已存在才能成功配置，否则会提示用户先完成相关的配置。[AC] capwap source interface vlanif 100
   Set the DTLS PSK(contains 6-32 plain-text characters, or 48 or 68 cipher-text characters that must be a combination of at least two of the following: lowercase letters a to z, uppercase letters A to Z, digits, and special characters):******Set the DTLS inter-controller PSK(contains 6-32 plain-text characters, or 48 or 68 cipher-text characters that must be a combination of at least two of the following: lowercase letters a to z, uppercase letters A to Z, digits, and special characters):******Set the user name for FIT APs(contains 4-31 plain-text characters, which can only include letters, digits and underlines. And the first character must be a letter):adminSet the password for FIT APs(plain-text password of 8-128 characters or cipher-text password of 48-188 characters that must be a combination of at least three of the following: lowercase letters a to z, uppercase letters A to Z, digits, and special characters):********Set the global temporary-management psk(contains 8-63 plain-text characters, or 48-108 cipher-text characters that must be a combination of at least two of the following: lowercase letters a to z, uppercase letters A to Z, digits, and special characters):********
   # 在AC上离线导入AP，并将area_1和area_2分别加入AP组“ap-group1”和“ap-group2”中。假设AP的MAC地址为60de-4476-e360，并且根据AP的部署位置为AP配置名称，便于从名称上就能够了解AP的部署位置。例如MAC地址为60de-4476-e360的AP部署在1号区域，命名此AP为area_1。​​​​​​​
   ap auth-mode命令缺省情况下为MAC认证，如果之前没有修改其缺省配置，可以不用执行ap auth-mode mac-auth。举例中使用的AP为AP5030DN，具有射频0和射频1两个射频。AP5030DN的射频0为2.4GHz射频，射频1为5GHz射频。[AC] wlan
   [AC-wlan-view] ap auth-mode mac-auth
   [AC-wlan-view] ap-id 0 ap-mac 60de-4476-e360
   [AC-wlan-ap-0] ap-name area_1
   Warning: This operation may cause AP reset. Continue? [Y/N]:y  
   [AC-wlan-ap-0] ap-group ap-group1
   Warning: This operation may cause AP reset. If the country code changes, it will clear channel, power and antenna gain configuration s of the radio, Whether to continue? [Y/N]:y  
   [AC-wlan-ap-0] quit
   [AC-wlan-view] ap-id 1 ap-mac dcd2-fc04-b500
   [AC-wlan-ap-1] ap-name area_2
   Warning: This operation may cause AP reset. Continue? [Y/N]:y  
   [AC-wlan-ap-1] ap-group ap-group2
   Warning: This operation may cause AP reset. If the country code changes, it will clear channel, power and antenna gain configuration s of the radio, Whether to continue? [Y/N]:y  
   [AC-wlan-ap-1] quit
   # 将AP上电后，当执行命令display ap all查看到AP的“State”字段为“nor”时，表示AP正常上线。
   [AC-wlan-view] display ap all
   Total AP information:
   nor  : normal          [2]
   Extra information: P  : insufficient power supply
   --------------------------------------------------------------------------------------------------
   ID   MAC            Name   Group     IP            Type            State STA Uptime      ExtraInfo
   --------------------------------------------------------------------------------------------------
   0    60de-4476-e360 area_1 ap-group1 10.23.10.254  AP5030DN        nor   0   15S         -
   1    dcd2-fc04-b500 area_2 ap-group2 10.23.10.253  AP5030DN        nor   0   10S         -
   --------------------------------------------------------------------------------------------------
   Total: 2

5. 配置WLAN业务参数

   # 创建名为“wlan-net”的安全模板，并配置安全策略。
   举例中以配置WPA-WPA2+PSK+AES的安全策略为例，密码为“a1234567”，实际配置中请根据实际情况，配置符合实际要求的安全策略。[AC-wlan-view] security-profile name wlan-net
   [AC-wlan-sec-prof-wlan-net] security wpa-wpa2 psk pass-phrase a1234567 aes
   [AC-wlan-sec-prof-wlan-net] quit
   # 创建名为“wlan-net”的SSID模板，并配置SSID名称为“wlan-net”。
   [AC-wlan-view] ssid-profile name wlan-net
   [AC-wlan-ssid-prof-wlan-net] ssid wlan-net
   [AC-wlan-ssid-prof-wlan-net] quit
   # 创建名为“wlan-net1”和“wlan-net2”的VAP模板，配置业务数据转发模式、业务VLAN，并且引用安全模板和SSID模板。
   [AC-wlan-view] vap-profile name wlan-net1
   [AC-wlan-vap-prof-wlan-net1] service-vlan vlan-id 101
   [AC-wlan-vap-prof-wlan-net1] security-profile wlan-net
   [AC-wlan-vap-prof-wlan-net1] ssid-profile wlan-net
   [AC-wlan-vap-prof-wlan-net1] quit
   [AC-wlan-view] vap-profile name wlan-net2
   [AC-wlan-vap-prof-wlan-net2] service-vlan vlan-id 102
   [AC-wlan-vap-prof-wlan-net2] security-profile wlan-net
   [AC-wlan-vap-prof-wlan-net2] ssid-profile wlan-net
   [AC-wlan-vap-prof-wlan-net2] quit
   # 配置AP组引用VAP模板，area_1上射频0和射频1都使用VAP模板“wlan-net1”的配置，area_2上射频0和射频1都使用VAP模板“wlan-net2”的配置。
   [AC-wlan-view] ap-group name ap-group1
   [AC-wlan-ap-group-ap-group1] vap-profile wlan-net1 wlan 1 radio 0
   [AC-wlan-ap-group-ap-group1] vap-profile wlan-net1 wlan 1 radio 1
   [AC-wlan-ap-group-ap-group1] quit
   [AC-wlan-view] ap-group name ap-group2
   [AC-wlan-ap-group-ap-group2] vap-profile wlan-net2 wlan 1 radio 0
   [AC-wlan-ap-group-ap-group2] vap-profile wlan-net2 wlan 1 radio 1
   [AC-wlan-ap-group-ap-group2] quit

6. 开启射频调优功能自动选择AP最佳信道和功率

   # 使能射频的信道和功率自动调优功能。
   [AC-wlan-view] ap-group name ap-group1
   [AC-wlan-ap-group-ap-group1] radio 0
   [AC-wlan-group-radio-ap-group1/0] calibrate auto-channel-select enable
   [AC-wlan-group-radio-ap-group1/0] calibrate auto-txpower-select enable
   [AC-wlan-group-radio-ap-group1/0] quit
   [AC-wlan-ap-group-ap-group1] radio 1
   [AC-wlan-group-radio-ap-group1/1] calibrate auto-channel-select enable
   [AC-wlan-group-radio-ap-group1/1] calibrate auto-txpower-select enable
   [AC-wlan-group-radio-ap-group1/1] quit
   [AC-wlan-ap-group-ap-group1] quit
   [AC-wlan-view] ap-group name ap-group2
   [AC-wlan-ap-group-ap-group2] radio 0
   [AC-wlan-group-radio-ap-group2/0] calibrate auto-channel-select enable
   [AC-wlan-group-radio-ap-group2/0] calibrate auto-txpower-select enable
   [AC-wlan-group-radio-ap-group2/0] quit
   [AC-wlan-ap-group-ap-group2] radio 1
   [AC-wlan-group-radio-ap-group2/1] calibrate auto-channel-select enable
   [AC-wlan-group-radio-ap-group2/1] calibrate auto-txpower-select enable
   [AC-wlan-group-radio-ap-group2/1] quit
   [AC-wlan-ap-group-ap-group2] quit
   # 在域管理模板下配置调优信道集合。
   [AC-wlan-view] regulatory-domain-profile name default
   [AC-wlan-regulate-domain-default] dca-channel 2.4g channel-set 1,6,11
   [AC-wlan-regulate-domain-default] dca-channel 5g bandwidth 20mhz
   [AC-wlan-regulate-domain-default] dca-channel 5g channel-set 149,153,157,161
   [AC-wlan-regulate-domain-default] quit
   # 创建空口扫描模板“wlan-airscan”，并配置调优信道集合、扫描间隔时间和扫描持续时间。[AC-wlan-view] air-scan-profile name wlan-airscan
   [AC-wlan-air-scan-prof-wlan-airscan] scan-channel-set dca-channel
   [AC-wlan-air-scan-prof-wlan-airscan] scan-period 60
   [AC-wlan-air-scan-prof-wlan-airscan] scan-interval 60000
   [AC-wlan-air-scan-prof-wlan-airscan] quit
   # 创建2G射频模板“wlan-radio2g”，并在该模板下引用空口扫描模板“wlan-airscan”。[AC-wlan-view] radio-2g-profile name wlan-radio2g 
   [AC-wlan-radio-2g-prof-wlan-radio2g] air-scan-profile wlan-airscan
   [AC-wlan-radio-2g-prof-wlan-radio2g] quit
   # 创建5G射频模板“wlan-radio5g”，并在该模板下引用空口扫描模板“wlan-airscan”。[AC-wlan-view] radio-5g-profile name wlan-radio5g 
   [AC-wlan-radio-5g-prof-wlan-radio5g] air-scan-profile wlan-airscan
   [AC-wlan-radio-5g-prof-wlan-radio5g] quit
   # 在名为“ap-group1”和“ap-group2”的AP组下引用5G射频模板“wlan-radio5g”和2G射频模板“wlan-radio2g”。[AC-wlan-view] ap-group name ap-group1
   [AC-wlan-ap-group-ap-group1] radio-5g-profile wlan-radio5g radio 1
   Warning: This action may cause service interruption. Continue?[Y/N]y 
   [AC-wlan-ap-group-ap-group1] radio-2g-profile wlan-radio2g radio 0
   Warning: This action may cause service interruption. Continue?[Y/N]y 
   [AC-wlan-ap-group-ap-group1] quit
   [AC-wlan-view] ap-group name ap-group2
   [AC-wlan-ap-group-ap-group2] radio-5g-profile wlan-radio5g radio 1
   Warning: This action may cause service interruption. Continue?[Y/N]y 
   [AC-wlan-ap-group-ap-group2] radio-2g-profile wlan-radio2g radio 0
   Warning: This action may cause service interruption. Continue?[Y/N]y 
   [AC-wlan-ap-group-ap-group2] quit
   # 配置射频调优模式为手动调优，并手动触发射频调优。[AC-wlan-view] calibrate enable manual
   [AC-wlan-view] calibrate manual startup
   # 待执行手动调优一小时后，调优结束。将射频调优模式改为定时调优，并将调优时间定为用户业务空闲时段（如当地时间凌晨00:00-06:00时段）。
   [AC-wlan-view] calibrate enable schedule time 03:00:00

7. 验证配置结果

   WLAN业务配置会自动下发给AP，配置完成后，通过执行命令display vap ssid wlan-net查看如下信息，当“Status”项显示为“ON”时，表示AP对应的射频上的VAP已创建成功。[AC-wlan-view] display vap ssid wlan-net
   Info: This operation may take a few seconds, please wait.
   WID : WLAN ID
   --------------------------------------------------------------------------------
   AP ID AP name RfID WID     BSSID          Status  Auth type     STA   SSID
   --------------------------------------------------------------------------------
   0     area_1  0    1       60DE-4476-E360 ON      WPA/WPA2-PSK  0     wlan-net
   0     area_1  1    1       60DE-4476-E370 ON      WPA/WPA2-PSK  0     wlan-net
   1     area_2  0    1       60DE-4474-9640 ON      WPA/WPA2-PSK  0     wlan-net
   1     area_2  1    1       60DE-4474-9650 ON      WPA/WPA2-PSK  0     wlan-net
   -------------------------------------------------------------------------------
   Total: 4
   STA搜索到名为“wlan-net”的无线网络，输入密码“a1234567”并正常关联后，在AC上执行display station ssid wlan-net命令，可以查看到用户已经接入到无线网络“wlan-net”中。[AC-wlan-view] display station ssid wlan-net
   Rf/WLAN: Radio ID/WLAN ID
   Rx/Tx: link receive rate/link transmit rate(Mbps)
   ---------------------------------------------------------------------------------
   STA MAC         AP ID Ap name   Rf/WLAN  Band  Type  Rx/Tx      RSSI  VLAN  IP address
   ---------------------------------------------------------------------------------
   e019-1dc7-1e08  0     area_1    1/1      5G    11n   46/59      -68   101   10.23.101.254
   ---------------------------------------------------------------------------------
   Total: 1 2.4G: 0 5G: 1
   当STA从AP1的覆盖范围移动到AP2的覆盖范围时，在AC上执行命令display station ssid wlan-net，查看STA的接入信息，可以看到STA关联到了AP2。
   [AC-wlan-view] display station ssid wlan-net
   Rf/WLAN: Radio ID/WLAN ID                                                     
   Rx/Tx: link receive rate/link transmit rate(Mbps)                             
   ----------------------------------------------------------------------------------------
   STA MAC          AP ID Ap name  Rf/WLAN  Band  Type  Rx/Tx      RSSI  VLAN  IP address     
   ----------------------------------------------------------------------------------------
   e019-1dc7-1e08   1     area_2   1/1      5G    11n   46/59      -58   101   10.23.101.254
   ----------------------------------------------------------------------------------------
   Total: 1 2.4G: 0 5G: 1
   在AC上执行命令display station roam-track sta-mac e019-1dc7-1e08，可以查看该STA的漫游轨迹。
   [AC-wlan-view] display station roam-track sta-mac e019-1dc7-1e08
   Access SSID:wlan-net    
   Rx/Tx:link receive rate/link transmit rate(Mbps) 
   c:PMK Cache Roam r:802.11r Roam s:Same Frequency Network
   ------------------------------------------------------------------------------
   L2/L3           AC IP                  AP name              Radio ID
   BSSID           TIME                   In/Out RSSI          Out Rx/Tx
   ------------------------------------------------------------------------------
   --              10.23.100.1            area_1               1
   60DE-4476-E370  2016/01/12 16:52:58    -51/-48              46/13
   L3              10.23.100.1            area_2               1
   60DE-4474-9650  2016/01/12 16:55:45    -58/-                -/-
   ------------------------------------------------------------------------------
   Number: 1

配置文件

SwitchA的配置文件#sysname SwitchA
#
vlan batch 10 101 to 102
#
interface GigabitEthernet0/0/1port link-type trunkport trunk pvid vlan 10port trunk allow-pass vlan 10 101port-isolate enable
#
interface GigabitEthernet0/0/2port link-type trunkport trunk allow-pass vlan 10 101 to 102
#
interface GigabitEthernet0/0/3port link-type trunkport trunk pvid vlan 10port trunk allow-pass vlan 10 102port-isolate enable
#
return
SwitchB的配置文件#
sysname SwitchB
#
vlan batch 10 100 to 102
#
dhcp enable
#
interface Vlanif10ip address 10.23.10.1 255.255.255.0dhcp select relaydhcp relay server-ip 10.23.100.1
#
interface Vlanif100ip address 10.23.100.2 255.255.255.0
#
interface Vlanif101ip address 10.23.101.1 255.255.255.0dhcp select interfacedhcp server gateway-list 10.23.101.2
#
interface Vlanif102ip address 10.23.102.1 255.255.255.0dhcp select interfacedhcp server gateway-list 10.23.102.2
#
interface GigabitEthernet0/0/1port link-type trunkport trunk allow-pass vlan 10 101 to 102
#
interface GigabitEthernet0/0/2port link-type trunkport trunk allow-pass vlan 100
#
interface GigabitEthernet0/0/3port link-type trunkport trunk allow-pass vlan 101 to 102
#
return
Router的配置文件#
sysname Router
#
vlan batch 101 to 102
#
interface Vlanif101ip address 10.23.101.2 255.255.255.0
#
interface Vlanif102ip address 10.23.102.2 255.255.255.0
#
interface GigabitEthernet1/0/0port link-type trunkport trunk allow-pass vlan 101 to 102
#
return
AC的配置文件#
sysname AC
#
vlan batch 100 to 102
#
dhcp enable
#
ip pool huaweigateway-list 10.23.10.1network 10.23.10.0 mask 255.255.255.0option 43 sub-option 3 ascii 10.23.100.1
#
interface Vlanif100ip address 10.23.100.1 255.255.255.0dhcp select global
#
interface GigabitEthernet0/0/1port link-type trunkport trunk allow-pass vlan 100
#
ip route-static 10.23.10.0 24 10.23.100.2
#
capwap source interface vlanif100
#
wlancalibrate enable schedule time 03:00:00security-profile name wlan-netsecurity wpa2 psk pass-phrase %^%#]:krYrz_r<ee}|Cq@9V(W{ZD$"\-R-HD_y.4#U4,%^%# aesssid-profile name wlan-netssid wlan-netvap-profile name wlan-net1service-vlan vlan-id 101ssid-profile wlan-netsecurity-profile wlan-netvap-profile name wlan-net2service-vlan vlan-id 102ssid-profile wlan-netsecurity-profile wlan-netregulatory-domain-profile name defaultdca-channel 5g channel-set 149,153,157,161air-scan-profile name wlan-airscanscan-channel-set dca-channelradio-2g-profile name wlan-radio2gair-scan-profile wlan-airscan radio-5g-profile name wlan-radio5gair-scan-profile wlan-airscan ap-group name ap-group1radio 0radio-2g-profile wlan-radio2gvap-profile wlan-net1 wlan 1radio 1radio-5g-profile wlan-radio5g vap-profile wlan-net1 wlan 1ap-group name ap-group2radio 0radio-2g-profile wlan-radio2gvap-profile wlan-net2 wlan 1radio 1radio-5g-profile wlan-radio5g vap-profile wlan-net2 wlan 1ap-id 0 type-id 35 ap-mac 60de-4476-e360 ap-sn 210235554710CB000042ap-name area_1ap-group ap-group1ap-id 1 type-id 35 ap-mac dcd2-fc04-b500 ap-sn 210235554710CB000078ap-name area_2ap-group ap-group2
#
return